Oxford Fabric Safety Lockout Maintenance Lockout Kit Portable Padlock Handy For 12 Locks

Lockey Oxford Fabric Safety Lockout Portable Padlock Handy for 12 Locks

Part No.: PH02

Portable Padlock Handy

• Made from durable industrial oxford fabric.
• Light, flexible devices can be carried on belt, accommodate 12 padlocks.
• With plastic spring for holding keys.
• The overall diameter is 183mm, lock hole diameter is 10mm.

Safety measures needed in the overhaul of chemical equipment

Necessary safety treatment before maintenance

1. Stop according to the predetermined plan.

According to the provisions of the maintenance plan and the requirements of each process, realize the timely exchange of information between departments, and stop the operation of related equipment at an appropriate time according to the maintenance plan.

2. Pay attention to the strength during pressure relief.

The process of pressure relief shall be carried out slowly, and it is prohibited to move or dismantle any chemical equipment without complete pressure relief.

3. Materials and garbage in the equipment shall be thoroughly cleaned.

Careful observation of the discharge port, prevent flammable, explosive and harmful substances are discharged into the sewer, or discharge to the ground, causing losses to people and things on the ground. When discharging, install the discharge pipe on the designated ground to avoid pollution to the surrounding environment. At the same time, the discharge shall be as clean as possible, and the toxic gas sent out that cannot be collected shall be properly handled.

4. Reasonably control the cooling and quantity reduction speed.

Prevent failure of high temperature equipment due to improper cooling treatment. For cooling high temperature equipment, it shall first cut off the heat source, and ventilation, with proper natural cooling to achieve the purpose of cooling, cutting can not directly pouring cold water for cooling, especially when the outside air temperature is higher, should slow cooling, prevent equipment damage caused by the temperature of severe changes, to prevent fire or explosion accidents, and at the same time to prevent the poisonous and harmful substances pollution to the environment.

5. The valve should be opened properly.

The correct way to open the valve should be after opening the valve buckle, stop for a moment, so that a small amount of material first through, the material flow of the situation to observe, when the material flow is smooth and then gradually adjust the valve, constantly accelerate. It is important to note that the steam valve should be carried out when the opening of the pipeline heat should be extra attention.

6. Stop the operation of high-temperature vacuum equipment.

First of all, the vacuum state should be eliminated to control the high-temperature equipment. When the temperature in the equipment is mentioned as the natural temperature, it can contact with the natural environment to prevent the air from entering the high-temperature equipment and causing combustion, explosion and other accidents.

Safety measures needed in the overhaul of chemical equipment

1. In the maintenance process of chemical equipment, it is necessary to ensure that the running equipment is in a stopped state.

2. During the maintenance of all kinds of electric machinery equipment, ensure the disconnection of the mechanical power, such as fuse, electric switch, or pour down, makes in the maintenance state of the machine to stop running and colleagues need when maintenance equipment necessary warning signs, words such as "maintenance, no closing".

3. If the light inside the equipment is poor, the lighting tools and power tools should be within the safe voltage range. The safe voltage in the dry equipment is less than or equal to 36V, and the safe voltage in the wet or closed environment is less than or equal to 12V.

4. If flammable substances exist in the maintenance area or equipment, it shall meet the requirements of explosion protection.

Lockey Safety Products Co., Ltd is a professional manufacturer in China, specializing in producing all kinds of safety lockout products to help avoiding industrial accidents, which are caused by the unexpected energization or start up of machines and equipments by the uncontrolled release of energy.

We provide all kinds of safety padlock, valve lockout, lockout hasp, electrical lockout, cable lockout, group lockout box, lockout kit and station.

In addition to providing professional lockout products, we also aim to provide you with the workable advice and provide a bespoke safety solution that is suited to your individual needs. We provide to both large and small businesses and we provide Lockout Tagout training and awareness courses.

Our manufacturing meets Standards like CE, ISO9001, OSHA, OHSAS18001, ATEX, etc.  We have hundreds molds to meet the locking requirements. We never stopped new products developing by our own research and development team, with many patented new designs.

Every year we participate in lots of professional trade shows, like A+A, Intersec, Safety in Action, Suntec. Our clients are from all over the world, such as USA, European, Asia, UAE, Australia, Southern America.

We’re always here for safety purpose. Let’s make our workplace more safer by using Lockey products.

Lockout is a choice you make, Safety is the destination Lockey achieve.